Datalogic-scanning Matrix 400 Manuel d'utilisateur Page 40
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MATRIX 400™ REFERENCE MANUAL
30
2
Setup (Function 3)
Once entered, the imager automatically performs Image Acquisition parameter calibration for
the specific code presented to it.
The Setup LED will blink until the procedure is completed.
The Setup procedure ends when the Image Acquisition parameters are successfully saved in
the reader memory, the Setup LED will remain on continuously and Matrix 400™ emits 3 high
pitched beeps.
If the calibration cannot be reached after a timeout of about 5 (five) seconds Matrix 400™ will
exit without saving the parameters to memory, the Setup LED will not
remain on continuously
but it will just stop blinking. In this case Matrix 400™ emits a long low pitched beep.
Learn (Function 4)
Once entered, the imager starts a procedure to automatically detect and recognize codes
which are presented to it.
The Learn LED will blink until the procedure is completed.
The Learn procedure ends when the Image Processing and Decoding parameters are
successfully saved in the reader memory, the Learn LED will remain on continuously and
Matrix 400™ emits 3 high pitched beeps.
If the calibration cannot be reached after a timeout of about 3 (three) minutes, Matrix 400™ will
exit without saving the parameters to memory, the Learn LED will not
remain on continuously
but it will just stop blinking. In this case Matrix 400™ emits a long low pitched beep.
2.5 MODEL DESCRIPTION
The Matrix 400™ reader is available in different versions according to the following
characteristics:
MATRIX 400 XXX-0X0
Illuminators
0 = BS (Base, No Illuminator)
Lens
0 = C-Mount (No Lens)
Sensor Size
4
= SXGA (1280x1024)
6 = UXGA (1600x1200)
Interface
0 = Serial
1 = Ethernet
- MATRIX 400™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- Required Accessories 12
- STEP 2 – CONNECT THE SYSTEM 12
- RAPID CONFIGURATION 13
- STEP 4 – FOCUS THE READER 16
- STEP 9 – TEST MODE 28
- Host Mode Programming 29
- Alternative Layouts 29
- Code Quality Verification 29
- 2 INTRODUCTION 30
- INTRODUCTION 31
- 2.3 ID-NET™ 35
- 2.4.1 X-PRESS™ Functions 38
- Test Mode (Function 1) 39
- Focus/Locate (Function 2) 39
- Setup (Function 3) 40
- Learn (Function 4) 40
- 2.5 MODEL DESCRIPTION 40
- 2.6 ACCESSORIES 41
- 2.7 APPLICATION EXAMPLES 42
- 3 INSTALLATION 49
- 3.2 MECHANICAL DIMENSIONS 50
- INSTALLATION 51
- 4.1 POWER SUPPLY 55
- 4.2 MAIN SERIAL INTERFACE 55
- 4.2.1 RS232 Interface 56
- CBX ELECTRICAL CONNECTIONS 57
- 4.3 ID-NET™ INTERFACE 60
- 4.3.1 ID-NET™ Cables 60
- 4.3.2 ID-NET™ Response Time 61
- Reference 65
- USER INTERFACE 65
- 4.5 INPUTS 66
- PH-1 Photocell (PNP) 67
- NPN Photocell 67
- PNP Photocell 67
- Input Device 68
- CE saturation 69
- Output Device 70
- Control Signal for 71
- LT-100, LT-200 or 71
- LT-300 illuminators 71
- Power to External 71
- Illuminator 71
- 4.8 USER INTERFACE - HOST 72
- 5.1 M16 19-PIN CONNECTOR 73
- 5.3 POWER SUPPLY 74
- 5.4 MAIN SERIAL INTERFACE 74
- 5.4.1 RS232 Interface 75
- MULITPLEXER 77
- 5.5 ID-NET™ INTERFACE 79
- 5.5.1 ID-NET™ Cables 79
- 5.5.2 ID-NET™ Response Time 80
- D-coded 85
- 5.8 INPUTS 86
- EXTERNAL TRIGGER 87
- Matrix 400™ 87
- 5.9 OUTPUTS 89
- 30 Vdc max 90
- 5.10 USER INTERFACE 91
- 6 TYPICAL LAYOUTS 92
- 6.2 PASS-THROUGH 94
- ID-NET™ 95
- 6.3 ID-NET™ 96
- Terminal 97
- Fieldbus Interface 98
- 6.4 RS232 MASTER/SLAVE 99
- 6.5 MULTIPLEXER 100
- TYPICAL LAYOUTS 101
- MATRIX 400™ REFERENCE MANUAL 102
- 7 READING FEATURES 103
- Code Resolution Conversion 105
- READING FEATURES 109
- 8 SOFTWARE CONFIGURATION 112
- 8.3 STARTUP 113
- 8.3.1 VisiSet™ Options 114
- SOFTWARE CONFIGURATION 115
- 8.4 CONFIGURATION 116
- 8.4.3 Calibration 122
- Not Readable 126
- Readable 126
- 8.6 STATISTICS 130
- 9 MAINTENANCE 131
- 10 TROUBLESHOOTING 132
- 11 TECHNICAL FEATURES 135
- GLOSSARY 137
- DECLARATION OF CONFORMITY 141
Produits connexes et manuels pour Matériel Datalogic-scanning Matrix 400
(2 pages)
(82 pages)Zanussi 113179 manuali
Manuali dei proprietari e guide per l'utente per Congelatori Zanussi 113179.
We fornisce 1 manuali pdf Zanussi 113179 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels